導線的連接情況下：單股銅芯導線的直線連接、T字形連接；雙股線的對接；多股銅芯導線的直線連接、T字形連接；不等徑銅導線的對接；單股線與多股線的T字分支連接；軟線與單股硬導線的連接；鋁芯導線用壓接管壓接；鋁芯導線用壓接管壓接。

先將兩導線芯線線頭成X形相交。互相絞合2～3圈后扳直兩線頭。

將支路芯線的線頭與干線芯線十字相交，在支路芯線根部留出5mm，然后順時針方向纏繞6～8圈后，用鋼絲鉗切去余下的芯線，并鉗平芯線末端。

將兩根雙芯線線頭剖削成圖示中的形式。連接時，將兩根待連接的線頭中顏色一致的芯線按小截面直線連接方式連接。用相同的方法將另一顏色的芯線連接在一起。

以7股銅芯線為例說明多股銅芯導線的直線連接方法。

以7股銅芯線為例說明多股銅芯導線的T字形連接方法

將分支芯線散開并拉直，再把緊靠絕緣層1/8線段的芯線絞緊，把剩余7/8的芯線分成兩組，一組4根，另一組3根，排齊。

用旋鑿把干線的芯線撬開分為兩組，再把支線中4根芯線的一組插入干線芯線中間，而把3根芯線的一組放在干線芯線的前面。